LED advertising car tires can not be ignored:
The oem numbers are in the below content.
LF20-15-025 L321-15-210C L330150025A L32115025K L32715210A AJ5715210C FS1H15140 32115025K
EP85-15-035AL2 FS8W15035
LF20-15-025 L321-15-210C L330150025A L32115025K L32715210A AJ5715210C FS1H15140 32115025K Mazda Radiator Fan,Radiator Fan Exhaust Fan,Engine Cooling Fan Assembly,Small Radiator Cooling Fans RUIAN HENGXIN AUTO PARTS CO.,LTD. , https://www.hengxinauto.com
First, the first LED advertising vehicle tire inflation should pay attention to safety. Always check the air pressure with a barometer to avoid over-inflating and bursting the tires.
Second, after stopping the vehicle, it is necessary to wait for the tire to cool before re-inflating, as the temperature of the tire will increase when the vehicle is driving, which has an impact on the air pressure.
Third, check the valve. If the valve stem and the valve core do not match with each Other, there are protruding recesses and other defects, and it is inconvenient to inflate and measure the air pressure.
Fourth, the advertising car should pay attention to clean inflatable. The filled air must not contain moisture and oil to prevent deterioration of the inner tube rubber.
Fifth, when the inflation should not exceed the standard air pressure and then deflate too much, can not be too long after the out inflated and over-inflated, if more than the standard will lead to excessive expansion of the cord, causing its strength to reduce, affect the LED The life of the car tires.
Sixth, LED advertising vehicle tires should be cleaned before filling the dust on the valve, do not loosen the valve core, after the completion of the application of soap bubble water (or saliva) painted on the valve, check whether the leak (if the leak will Produce small bubbles) and tightly seal the valve cap to prevent sediment from entering the interior of the valve.
7. Some advertisement vehicles are equipped with other tires. For example, when the radial tire is inflated, its sinking volume and grounding area are large because of the structure. It is often mistaken for under-inflation and over-inflated; or because it sinks. The amount and the ground contact area are inherently large, and they are mistaken for a sufficient amount when the air pressure is insufficient. Apply a standard barometer to measure. The radial pressure of the radial tires should be 0.5-1.5kg/cm2 higher than that of ordinary tires.
About Mazda radiator fan, we provide 10 mazda radiator fans.
ZL01-15-025B E35815140 ZL0115025A ZL0115025C ZL0115150 ZL0115210A ZL0115210B ZL0415210B ZL0415025C
ZL-01-15-035L B59515035C B59515140 B59515150A B59515210A FS2V15035F
PA10-15-025M1 PD1115035M1
PA10-15-035M1 PD1115025M1
Z602-15-025B LFN7-15-025B Z60215025C
ZJ36-15-025
ZL04-15-025CL1 FP8515025A
1680008780 LF4K15025
ZL01-15-025B E35815140 ZL0115025A ZL0115025C ZL0115150 ZL0115210A ZL0115210B ZL0415210B ZL0415025C
ZL-01-15-035L B59515035C B59515140 B59515150A B59515210A FS2V15035F
PA10-15-025M1 PD1115035M1
PA10-15-035M1 PD1115025M1
Z602-15-025B LFN7-15-025B Z60215025C
ZJ36-15-025
ZL04-15-025CL1 FP8515025A
EP85-15-035AL2 FS8W15035
1680008780 LF4K15025