The washing and sweeping truck adopts Dongfeng Tianjin DFH1180EX8 type national six second category vehicle chassis modification, adding auxiliary engine, fan, high pressure water pump, clean water tank, trash can, left and right vertical sweep, wide suction nozzle with water spray rod, low pressure washing system, The sweeping dust suppression system, hydraulic system, special device electric control system and sub-frame etc. are refitted.  The auxiliary engine drives the fan and high-pressure water pump, and the auxiliary engine uses a Dongfeng Cummins six-cylinder 170-horsepower diesel engine. The fan uses an 8.0 high-pressure centrifugal fan, which has high efficiency and large air volume, with a maximum air volume of 23,500m 3 /h. The high-pressure water pump adopts the internationally-known plunger pump with suitable flow and high pressure, and the maximum allowable pressure is 10MPa Consultation hotline; 15271341199  The clean water tank makes full use of the vehicle-mounted space, and has a large volume with a volume of 9m 3 . The trash bin adopts single stainless steel structure, dumping and unloading, with high-pressure self-cleaning device. The self-cleaning device can help unloading and cleaning the inside of the trash can when unloading the trash can.  The left and right vertical scanning is a single scanning plate, which reduces the number of brushes and the consumption of brushes, and can reduce the cost of use. The left and right vertical sweeps are controlled separately, and different operation modes such as left sweep, right sweep and full sweep can be realized. The width of the suction mouth of the wide suction nozzle reaches 2418mm, ensuring that the total working width is greater than 3.5mm. The 4 height-adjustable nozzle wheels can adjust and ensure a reasonable gap between the nozzle and the road surface. The suction nozzle has a built-in high-pressure water spray rod, and as many high-pressure washing nozzles as possible are arranged inside the suction nozzle, which not only has a good cleaning effect, but also minimizes the secondary pollution caused by the high-pressure water flow.  The left and right spray rods are installed on the suction cups and move up and down with the suction cups. The structure is simple and compact, which ensures that the height of the spray rods from the ground is constant and achieves the best cleaning effect. The open hydraulic system drives the left and right vertical sweeping and lifting, the left and right sweeping pan rotation, the suction nozzle lifting, the opening and closing of the rear door of the trash can, and the dumping and resetting of the trash can.  The power take-off on the gearbox side of the chassis drives the low-pressure water pump to realize the low-pressure flushing function of the sprinkler, and one-button start and stop operations.  The CSC5180TXSD6 sweeper has multiple functions such as road cleaning, road cleaning, curb cleaning, curb and curb facade scrubbing, low-pressure washing, spray dust removal, etc. There are multiple operation modes such as "full wash and sweep", "left wash and sweep", "right wash and sweep", "full sweep", "left sweep" and "right sweep" to choose from. Choose "full washing and sweeping" mode to clean the square and pavement, the cleaning efficiency is high and the effect is good, and the cleaning rate is more than 90%. Choose "left washing and sweeping" or "right washing and sweeping" mode to clean the road surface and curbs, and scrub the curb facade. When road cleaning or road cleaning operations are required, the road sweeping mode can be selected. When spray dust removal is required, the spray device can be turned on to perform spray dust removal operations. The road surface can be washed with low pressure like a sprinkler.  CSC5180TXSD6 sweeper is suitable for cleaning operations such as mechanized cleaning, sweeping, spraying and dust suppression of urban roads, highways, squares, airports, docks, tunnels, bridges, isolation walls, curbs and curb facades. Consultation hotline; 15271341199 Item Main performance parameters Car type Dongfeng Tianjin Vehicle model CSC5180TXSD6 washing and sweeping truck Chassis model, category, manufacturer DFH1180EX8 Class II Dongfeng Motor Co., Ltd. Emission Standards GB3847-2005, GB17691-2018 National Ⅵ hair move machine Host Chassis engine model and manufacturer B6.2NS6B210 Cummins Engine Co., Ltd. Power (kw) 154 Horsepower (ps) 210 Displacement (ml) 6200 Auxiliary engine Clean engine model Cummins 170 horsepower supercharged auxiliary engine Power (kw) 125 Horsepower (ps) 170 Displacement (ml) 5900 Fuel type No. 0 light diesel (shared diesel tank with chassis) vehicle Basic parameter Dimensions (length X width X height) mm ★ 8630*2500*3100 Wheelbase (mm) 5000 Tires 10.00R20 18PR steel wire tire Number of tires 7 (including 1 spare tire) Wheelbase Front wheel (mm) 1876 Rear wheel (mm) 1820 Rated occupant 3 people Front suspension/rear suspension (mm) 1430/2220 Approach angle 17° Departure angle 13° Ground clearance (mm) 320 Rated load (kg) 5970 Curb weight (kg) 11900 Maximum total mass (kg) 18000   Dedicated performance parameters Trash bin volume (m 3 ) 7 Clean water tank volume (m 3 ) 9 Sweeping width (mm) 3000-3500 Cleaning speed (km/h) 3-15 Cleaning operation speed (km/h) 15-20 Maximum cleaning capacity (m 2 /h) 48000 Suction capacity Density (g/cm 3 ) 2.0 Mass (kg) 1.5 Suction particle size (mm) ≥100 Trash bin dump angle ≥45° Cleaning efficiency ≥96% Operating noise (db) < 88 Meet the requirements of GB7258 Driving performance parameters Drive type 4×2 rear axle drive Suspension type Leaf spring Number of leaf springs (front/rear) 8/10+7 Braking type Double circuit pneumatic brake, drum type Braking distance (full load 30km/h) ≤10m Maximum speed (km/h) 89 Minimum turning radius (m) 8 Maximum grade ≥30% Clutch system Single-plate dry-type diaphragm spring clutch, hydraulically operated Transmission system Mechanical 5-speed transmission with synchronizer, manual Engine fuel consumption Driving (L/100km) Operation (L/h) Operation (L/10000m 2 ) ≤14 ≤8 ≤5 Dust suppression system Water spray form Low pressure mist Main components Imported high-pressure pump, water filter, pipeline, stainless steel spray frame, high-pressure nozzle, etc. High pressure pumps CPX036 Installation location Sweeping and dust reduction Scan the left and right front Vacuum dust In the suction cup suction port Control type Electronic control, one-key operation  Hydraulic system Type Open, electric control centralized operation Main components Gear pumps, cycloid motors, hydraulic cylinders, solenoid valves, manifold blocks, high-pressure pumps, etc. Cycloid motor Sanyo Motor gear pumps Changyuan Machinery Hydraulic cylinder Hypress hydraulic cylinder Hydraulic cylinder seals Dingji Hydraulic tubing Guangzhou Tianhe Solenoid valve group Hypres (Sino-Italian joint venture) Shockproof pressure gauge IMT Return oil filter Sophia System overflow pressure Mpa 10-12 Hydraulic oil tank volume L ≥60 Electrical system System composition It is composed of chassis vehicle circuit, auxiliary engine electrical part and special working device operation control circuit. Chassis vehicle system voltage (V) twenty four Working device system voltage (V) 12 Panel composition of electric control box Auxiliary engine tachometer, auxiliary engine water temperature gauge, oil temperature alarm device, various operation control switches Control switch Shanghai Schneider (Sino-French joint venture) Programmable Logic Controller Bai Zhaofu breaker Hager Battery model The accurate definition of a crusher hammer head should be the hammer head of a hammer crusher. The hammer head is one of the core components of a hammer crusher, arranged on the hammer shaft of the crusher rotor. The hammer head directly strikes the material during high-speed operation of the crusher, ultimately crushing it into a suitable material particle size. The hammer heads of crushers on the market can be divided into two types based on manufacturing processes: casting and forging, but their wear resistance is different. Due to the need for good wear resistance at the head and sufficient toughness at the handle when crushing materials, materials such as alloy steel, high manganese steel, cast steel, and high chromium cast iron bimetallic composites are usually formed in one forging or casting process, with corresponding heat treatment processes being more economical. Hammer head,Forging hammer head,Steel alloy hammer head SiChuan TieYing Machinery Manufacturing CO.,LTD; , https://www.tieyingcrushers.com
Hammer Head